How to mount a fixed projector screen on drywall

If you are looking How to mount a fixed projector screen on drywall or some other elevated surface, then you should check out this post!

Nowadays, there is no need to be limited to using a projector screen that hangs from the ceiling. If you have drywall, then you can mount a fixed projector screen instead. This way, you can have it permanently attached to the drywall or ceiling, and then adjust the screen angle by tilting its surface.

Mounting a projector screen on drywall is a great alternative to traditional mounting methods, like tripods or pull-up screens, and will save you a lot of time. Additionally, drywall is a versatile material that can be used to create walls and ceilings in your home while mounting a projector screen on drywall can be tricky.

In this article, we will talk about the projector screen mounting process from start to finish, and also provide you step by step guide, methods, tips, and other important solutions!

Here we go!

How to mount a fixed projector screen on drywall

How to mount a fixed projector screen on drywall?

If you’re mounting a fixed projector screen on drywall, just remember that there are two different ways to mount it. Either way, the drywall isn’t going to be enough to support the bolts and hooks.

The first way is to install the drywall anchors into the wall. You may need screws or nails depending on your drywall, but after you slide the anchors all the way in, they’ll expand to hold your screen up. After you have it secured with screws, slide the bolts through your projector screen and into the anchors on your wall.

The second method is similar but doesn’t require that you install any anchors. You’ll need heavy-duty washers, like the kind you use for hanging a door. You’ll also need bolts with big heads and lots of grooves; the flat metal disks usually found on bolts will work fine.

This is not a very long-lasting method and is only good for temporary use, but it does make it easier to take your screen down if you decide you don’t need it.

Step by step process to mount a fixed projector screen on drywall

  1. First, you’ll have to find the studs in your wall, along the edge of where the screen will be mounted. If you plan on using widescreen, you should place the support post every 16 inches.
  2. After finding and marking your studs with a pencil, take your drill and create pilot holes where your support posts will be mounted.
  3. Assemble the projector screen with the hooks, including all necessary hardware. Make sure to use proper-sized lag bolts that are long enough for your application.
  4. Now mount the support post on the wall where it has been marked using two of the same-sized lag bolts. Tighten until solid.
  5. Assemble all necessary hardware with the screen and mount it securely on the support post that you just mounted to the wall.
  6. Finally, hang your projection equipment to finish! You may need a hand from someone as each projector comes with its weight limit, usually about 30 pounds or less.

Methods to mount a fixed projector screen on drywall

There are many different methods to mount a fixed projector screen on drywall. We have reviewed some of the most common methods below.

Mounting bracket with toggle bolts

The first way to mount a fixed projector screen on drywall is by using mounting brackets and toggle bolts. Toggle bolts are used to hang heavy objects on drywall. They require no drilling and can be inserted easily into the wall. After screwing in the toggle bolt, it acts like a spring expanding inside the wall cavity to give you a solid mount for your projector screen. This is considered an anchor system since you are using screws that expand behind the wall.

Drilling

The second way to mount a fixed projector screen on drywall is by drilling. You will need to drill small holes in the mounting area of your wall. After you have drilled the holes, insert screws through the holes and secure them with washers. A larger screw must be used on drywall because toggle bolts are not large enough for this type of surface.

Wall anchors

Another method to mount a fixed projector screen on drywall is using wall anchors. These are small plastic anchors that require no drilling and can be inserted easily into the wall. This system does not provide as much support as the toggle bolt because there is no screw expanding, so you need to make sure these are installed properly.

L-brackets

Another method to mount a fixed projector screen on drywall is using L-brackets. These brackets give extra support by crossing over each other once installed into the wall. You also do not need to use any screws or drilling since they rely on the screws that come with your wall mounting kit. This is an anchor system like the toggle bolts.

Screws

The last method to mount a fixed projector screen on drywall is using screws directly into the wall. This requires very little time, but you will need to drill holes into the wall and then screw in the screws from your mounting kit to connect your projector screen.

Techniques to mount a fixed projector screen on drywall

Mounting a projector on the drywall is not as difficult as it looks. You may use two L-shaped metal brackets that are attached to a stud on one side and have a hook on the other. This is then hooked to the projector mount hole, which will give you that extra height.

Using the L-bracket and a wall hook

The first step is to get the hardware components, which include two heavy-duty L brackets (for strength), one 1 inch wood screw (for attaching the bracket to the stud), and two hooks that are 2 inches long (for the projector to hang on). To get the exact measurements, look at your projector’s manual.

Next, take your projector and measure the distance between its mounting holes (the two round flanges). The distance should not be more than 8 inches. For example, mine is 7 3/8 inches (187 MMS).

Now if you called a professional for this task, they would charge you money to take all these measurements for you.

Using the J-shaped brackets

The second step is to attach one hook to one of the J-shaped brackets, which are 1 by 2 inches wide and 6 inches long. The opening for mounting has a center hole that can be used with any 1-inch wood screw. Attach one hook to the flat side of the bracket, as it is less likely to be visible after the screen is mounted.

Once these steps are performed, two brackets can be attached to each J-shaped bracket; this will ensure that the screen will remain flat after it is mounted.

Tips to mount a fixed projector screen on drywall

  1. To drill a hole to the wall to put the screw in to place the projector screen to the wall to make sure to mount a fixed projector to drywall.
  2. Using a stud finder to detect where is the stud to be mounted on to place the screws that will hold the projector screen to the wall for max strength
  3. To use a drill with the right size bit to have less chance of crack or break off to stud to place the screw to mount a fixed projector to drywall
  4. You should know the right size of screw to match with the type of wall or stud to mount a fixed projector screen on drywall
  5. If you use a leveler to measure it should be straight before hanging it on to place the screws that will hold the projector to mount fixed drywall.

Frequently ask questions

Is it difficult to mount a screen to drywall?

Not at all. It is rather simple to do so. All you require are the right tools and follow the necessary steps to get it done in no time. You should however keep in mind to allow enough slack so that your projector can be moved around to adjust to different viewing angles.

What tools to use to mount a projector to drywall?

You will need to have some basic hand tools at your disposal to get the task done. For the mounting of the projector, you will require screws and nuts to screw onto to wall studs.

What type of nails to use to mount a projector to drywall?

Heavy-duty nails are best to use during the mount. When you get to this stage of wall mounting, there is no need to be frugal with your items since they will provide more than enough support for your screen.

Is it possible to wire a screen into an existing electrical setup to save money?

Yes, it is possible to wire a screen into your existing electrical setup, but there are certain things to take into consideration to prevent accidents from happening. Wiring the screen to an existing outlet implies that you will need to use more than one to supply electricity to the screen.

How to attach a projector to drywall to prevent rattling?

There are several things to consider to prevent from happening this. For one, you should make sure to attach screws to the wall studs to provide enough stability to hold up your projector.

Also, Read

Best projector for android under 100 | Top 2022 Picks

How to turn on Promethean Projector without remote | Promethean Projector Guide

Best outdoor projector under $100| Top Picks 2022

Conclusion

Mounting a projector to drywall can be simple to achieve, but it does require some basic tools to get the job done. The most important thing to keep in mind is to prevent any accidents from happening by making sure to use heavy-duty nails for this project.

Use at least 4 to 6 nails to ensure that your screen remains firm against the wall to prevent rattling.

We hope you like our article about how to mount a fixed projector screen on drywall. If this content was helpful then do not forget to leave your feedback!